A, paper cutting
1), preparation:
Check the wallpaper model and guest buy consistency inspection constructionquality, batch is the same, whether for continuous serial number. Two rolls of wallpaper out, observe whether there is a difference.
2), wallpaper cutting:
The first step: how can the wallpaper should cut first, determine the height of the building, to determine a wallpaper, 10M can cut pieces of wallpaper.Secondly, the general wallpaper most likely is a unit of 53m, but if 53cm is the two unit. A unit of length is 26 5cm, if the 53cm into three units, is a unit of 17.7cm, and so on, so the general according to the flower wallpaper on theflower consumption and housing height to determine a wallpaper can cutpieces.
Second step: according to the step of the calculated height, tailoring wallpaper* Note: on the decal length must be reserved for the 5cm more than the wall,for trimming. Secondly: cut a pencil, application in the back of the wallpaper.Indicate the serial number and direction * Note: A, the number should be unified, digital, writing should be clear, not vague B, Fang Xiangying unifiedlabel direction again: flower wallpaper in the cut second pieces of wallpaper,and a take the alignment, then cutting at the end of each cut three shouldcheck there is no difference, all the wallpaper should be cut. * Note: A, after allthe wallpaper cut, should according to the serial number of stacked. B, leftzero material can not be discarded, should be placed neatly beside.
Two, glue
1) modulation, glue
Modulation of A, usually with wallpaper glue powder or special stickers glue,according to the instructions on the packaging contents, were preparedaccording to the proportion of. Proportion: each pack powder 160 grams and4 kilograms of water, in order to enhance the adhesive fastness 10% should be added to the adhesive. Modulation methods: clean water into the bucket,and water mixing, and then slowly add the wallpaper powder, continuous stirring for 1 minutes, so that the powder is completely dissolved, placed 5minutes after stirring for 30 seconds, and then added according to the proportion of glue evenly stirred. Be careful.
● stirring stirring rod should be toward the stir in one direction, strength should be uniform, speed keeping.
● add glue should be added slowly, not too fast.
● mixing should fully mixing, stirring good adhesive should be uniform color.
Modulation of B, special glue
In the joint and the upper and lower edges; glue adhesive should be higher than the general glue adhesion stronger. It should be re formulated special glue. Proportion: 50% should be added to the white in the preparation of goodwallpaper powder, modulation method is consistent with the like glue.
2), wallpaper glue
A, the drum in the prepared glue for 30 seconds.
B, the drum is evenly painted on the back of the wallpaper.
Be careful.
● roller coating should be moving in the same direction roller, roller and thewallpaper into 45 degrees gently rolling brush. Unable to roll back the brush, it is easy to make the wallpaper set.
● populations, the action should be smooth, uniform intensity, a hand drum,on the other hand is fixed on the no brush glue place; lest wallpaper roll.
● all finished, with a small brush, in the wallpaper edge with special glue(wallpaper powder and glue ratio l:1) and then brushing again.
3), placing the wallpaper glue after
Folding A wallpaper, wallpaper glue, should be first wallpaper with LM as afolded, and then as a standard, uniform dorsal fold, fold back to the left for a period of time, and the short.
Be careful.
● should be completely folded
● especially around the edge can not leave gaps around the edge, so as to avoid glue quickly.
B, wallpaper wallpaper folded placed time should be placed 3 minutes, the longest no more than 15 minutes.
C, note (a) coating glue, one with 4-5, but if affixed to the corner, a brushing 3pieces. (b) using a small brush glue evenly.
Be careful.
● glue can not smear too much, should be evenly two times.
● edge glue should be thoroughly.
Three, wallpaper paste
1), on the walls
Wallpaper paste should be carefully examined before the wall and the corneris smooth, dry, clean, burnish is in place, it should be before the wall work standards in the wallpaper. Position selection posted first wallpaper.
A if the larger pattern choice. The most prominent wall began posting.
B common patterns or small wallpaper can be close to the main light source is wide side walls began posting.
C finally wall paper in an inconspicuous place to end.
In the first picture will be posted on the wall wallpaper, Yin angle at 50cm distance. Top top-down from smallpox by gravity hammer, delete the verticalalignment, pencil from top to bottom, light by gravity hammer drum, draw someLCM short-term as a vertical reference line.
2), how on the wall
A, the first piece of wallpaper brush glue. Unscrew the upper part near the vertical line.
Be careful.
Close to the vertical line to the light from the vertical line to 1cm or so, and then gently moving wallpaper, wallpaper edge until completely close to the vertical line.
B, a scraper scraping half wallpaper
2, the housing settlement of Yin angle
1) measured from the last picture wallpaper center to the concave corner, plus 2.5cm, according to the width of cutting a piece of wallpaper.
2) the section of the wallpaper paste, let it aligned and connected with the label wallpaper and leveled in the concave corner.
3) with scraper scraping the protruding part on the stick to walls, and thescraper on the glue dry earned.
4) will be another piece of wallpaper and wallpaper paste a picture overlap,the flower wallpaper alignment, and turn to the other side of the wall.
5) in the shade horn will drag back leveled shade horn.
Be careful.
First hand slowly the wallpaper to corner, again slowly scraper back cornersmoothing, do not force so as not to hurt the wallpaper.
6) at a distance of Yin angle 2mm along the blade repaired crease, a rulerwith the knife, from top to bottom incision.
7) remove redundant wallpaper, and with a white towel or sponge to wipe awaythe excess glue.
G, switch the paste method
Method: the wallpaper affixed to the switch port, and then use the wooden handle brush flat, with a knife in the above diagonal cross, but to the appropriate force, do not scratch the switch, a scraper against the switch with the knife edge, homeopathic cut redundant wallpaper.
Method two: wallpaper affixed to the switch, in the four corner device, toward the center with a knife cut four points, in the distance switch long edge LCMcut a parallel line from switch sides short edge distance is 1cm, the midpoint in the equal line of the picture is good with the beauty industry, these a vertical line, from the lower edge of the lower 3cm, two points with a knife and a vertical line drawn wire, scraper against the switch box with the edge of the knife cut away excess wallpaper.
H, doors and windows of the paste method
The general housing if not do Mentao, Chuangtao upper words have two parts to be wallpaper practices are as follows:
1) attached to a wallpaper nearest the window left right on the edge of thewallpaper paste is good, and the excess portion extending in the upper and lower window with good.
2) the middle window empty part with a knife along the lower edge of the window on to draw parallel lines.
3) will cut out part of the package into the window of about two edge.
4) cut fraction of the material and just stay in the left window edge overlapextension.
5) along the edge of a ruler wallpaper overlap with the knife, cut down.
6) remove redundant wall paper, and with the white towel or sponge to wipe away the excess glue.
Three, repair order
After all the wallpaper, should carefully check, check the contents:
1) joints are aligned, become warped edge.
2) if bubbles.
3) whether the pattern does not match.
4) play the creases, as in any of the following circumstances should remedyaccording to the following method:
A, joint release with knife: joint, into the glue from the slit, a scraper is suitableskin, wipe off the excess glue.
B, bubble: cut with a knife, in the opening into the glue, with suitable wrench tosmooth, wipe off the excess glue.
C, the pattern does not agree: because the building is not accurate, such asground settlement caused by uneven, not to spend can let it appear in an inconspicuous corner.
D, fold: open folds with a knife, and glue roller, with smooth, if uneven, switch to "fill the ingot" mode.
E, wet patch: don''t usually see wallpaper and wall defect; may be the problem,want to ask the experts.
F, black spots are said: wall has problems such as: moldy, seepage; removewallpaper processing good moisture, mildew and coated with glue.
On the wall treatment
Objective: wallpaper construction is the most important part of the wholeconstruction process, has an important effect on the wallpaper pastewallpaper construction.
1, in principle to be smooth, dry, color evenly wallpaper.
2, cement, brick wall: itself is relatively flat, flat with putty, brush on the thinvarnish can wallpaper.
3, gypsum board, plywood and blockboard: seams exist, so the first batch of flat seams again.
Patching putty: just add more glue (vinyl acetate resin), so that the seam is firm, not split.
Number of flat with putty: as long as the addition of a small amount of glue, so that the sand mill.
4, gypsum powder and glue to replace the number of flat with putty, canaccelerate the drying, shorten construction time.
5, wall: the wall is not the existence of solid powder, should be removed sanding, leveling, brush on the basement membrane can be wallpaper.
Light wall: the wall is very smooth (such as painted wall), is not easy to absorbglue, is not easy to dry, then force will decline, so must be sanded beforewallpaper.
6, paint the wall is very suitable for this wallpaper, but need to sand grindingprocessing wallpapered basement membrane to construction. Surfacepretreatment of wallpaper and paint the walls in the pretreatment of roughly the same.
7, the basement membrane function: basement membrane to cure and protectthe putty layer, also can strengthen the bottom wall waterproof, mould proof function, but be Nizi completely dry before painting. (basement membrane issurrounded by product, easy to dry, is the traditional varnish substitute).
8, any wallpaper can not water construction.
9, before the construction of basement membrane wall to brush.
